**********************************************************************
Media Pro 4000 Brief			Date: February 2nd 1999

File:	Firmware_FileName_Conventions_BR020299.txt
Module:	All MP4000 Modules with Firmware			
Title:	Typical Firmware FileName Conventions
**********************************************************************

1)	Typical Firmware FileName Conventions

	a) Most Modules Firmware starts with
	 the same first 3 letters as the module itself.
	   ie: DSM-4010 uses dsm4kd08.cod
                     ^^^
	b) A b, or bt in the middle of the .cod filename indicates
	 that the firmware is the module's BOOT firmware.
	   ie: DSM-4010 uses dsm41b01.cod
                          ^
	c) A d,dl or pgm in the middle of the .cod filename indicates
	 that the firmware is the module's DOWNLOAD
	 (application program) firmware.
	   ie: DSM-4010 uses dsm4kd08.cod
                          ^
	d) The remaining ending characters in the file name indicate
	 the version of the firmware.
	  ie: DSM-4010 dsm4kd08.cod
                     ^^

2)	Exception: The ICM download (application program)
	 Firmware is named as follows.

	a) First 2 characters reflect the MP4000 software version
	 16 = 16bit software,  32 = 32bit software.

	b) The next 2 characters reflect the ICM Module version
	 10 = ICM-4010,  20 = ICM-4020

	c) The remaining ending character in the file name indicate
	 the version of the firmware.

	d) ie: 3220109b.cod is for 32bit MP4000 Software,
	 ICM-4020, Firmware version 109b.


3)	Name Examples: (at some time in the past)

	a) ABM-4010 Download Firmware is : ABMrtD00.cod

	b) AOM-4010 Download Firmware is : AOM5pgm2.cod
	   AOM-4010   BOOT   Firmware is : AOM5bt01.cod

	c) ASM-4020 Download Firmware is : ASM42d03.cod
	   ASM-4020   BOOT   Firmware is : ASM42b03.cod

	d) DSM-4010 Download Firmware is : DSM41d09.cod
	   DSM-4010   BOOT   Firmware is : DSM41b02.cod

	e) DSM-4020 Download Firmware is : DSM42d60.cod
	   DSM-4020   BOOT   Firmware is : DSM42b21.cod

	f) ICM-4020 Download Firmware is : 3220115c.cod
	   ICM-4020   BOOT   Firmware is : ICMbt228.cod

	g) IMC-4010/20 Download Firmware is : IMC_115e.cod

	h) LCM-4020 Download Firmware is : LCMdl277.cod

	i) SEM-4020 Download Firmware is : SEMdl038.cod

	j) TCM-4010 Download Firmware is : TCM4Kd04.cod
	   TCM-4010   BOOT   Firmware is : TCM4Kb02.cod


4)	Updating Firmware

	a) In most cases it is only necessary to update the
	 Download Firmware, and not necessary to update the
	 Boot firmware.

	b) Most modules will not display firmware information
	 when queried if they are running only the Boot,
	 Nor will they verify the boot.

	c) If the programming of the Boot seemed successful,
	 and the Module does not respond to version info requests,
	 or verify the boot, proceed with programming the Download
	 Firmware, then Verify both the download Firmware,
	 and the Boot Firmware.

	d) Once the Download Firmware is running, the module should
	 respond to the Firmware version requests,
	 as well as be able to verify the Firmware.

	e) If it is necessary to update the Boot Firmware on a Module,
	 a jumper may need to me moved on some modules,
	 before programming the boot,
	 and moved back after the boot is programmed and verified. 

	f) See the Jumper information in the manual for the module
	 in question, or contact Anitech Systems
	 for further information.

	g) NOTE: It is imperative that once the programming
	 of the Boot is started, that it not be interrupted
	 (reset, turned off, unplug the comm cable, ...),
	 or the module may become unusable
	 (requiring a new Boot Flash to be installed).


5) Boot Program Enable Jumper Example:

	a) DSM-4010, requires a jumper to be moved before programming
	 the Boot.

	b) The Jumper (E2) is located near the center of the back edge
	 of the Module, near the bottom edge of the Field connector.

	c) For normal operation, the jumper should be
	 E2: 1-2 (disabled).
	 To program the Boot the jumper should be E2: 2-3 (enabled).

----------------------------------------------------------------------
Specifications subject to change at any time.

The data in this document incorporates proprietary rights of
Anitech Systems Inc., 25021 Anza Drive, Valencia, CA  91355  USA
Phone (805) 257-2184     Fax (805) 257-2025
Phone (661) 257-2184     Fax (661) 257-2025
Email Mail@Anitech-Systems.com     Web http://www.Anitech-Systems.com

Any party accepting this document does so in confidence and agrees that
it shall not be duplicated in whole or in part, nor disclosed to others,
without the consent of ANITECH SYSTEMS.